SERVICE DATA AND SPECIFICATIONS (S.D.S.) — Inspection and Adjustment (Cont'd) / Camshaft & Camshaft Bearing / Cylinder Block
EM-61spec tableGrade No. 2 standard inner-diameter inch value reads "2.9757 - 2.7961" in the source; the first digit "2.9" appears to be a printing error (the mm range 71.010 - 71.020 converts to ~2.7957 - 2.7961 in). Transcribed verbatim with [?] marking on the questionable digit.
Inspection and Adjustment (Cont'd)
CAMSHAFT AND CAMSHAFT BEARING
Camshaft
NOTE
Unit: mm (in)
Cam height "A" — Intake
CG10DE38.005 - 38.195 (1.4963 - 1.5037)
CG13DE39.880 - 40.070 (1.5701 - 1.5776)
Cam height "A" — Exhaust
CG10DE38.005 - 38.195 (1.4963 - 1.5037)
CG13DE39.880 - 40.070 (1.5701 - 1.5776)
Cam wear limit
CG10DE0.20 (0.0079)
CG13DE0.20 (0.0079)
Camshaft bearing
NOTE
Unit: mm (in)
Camshaft journal to bearing clearance
Standard0.045 - 0.086 (0.0018 - 0.0034)
Limit0.15 (0.0059)
Inner diameter of camshaft bearing — No. 1
Standard28.000 - 28.021 (1.1024 - 1.1032)
Limit—
Inner diameter of camshaft bearing — No. 2 to No. 5
Standard23.500 - 23.521 (0.9252 - 0.9260)
Limit—
Outer diameter of camshaft journal — No. 1
Standard27.935 - 27.955 (1.0998 - 1.1006)
Limit—
Outer diameter of camshaft journal — No. 2 to No. 5
Standard23.435 - 23.455 (0.9226 - 0.9234)
Limit—
Camshaft runout [T.I.R.*]
StandardLess than 0.02 (0.0008)
Limit0.1 (0.004)
Camshaft end play
Standard0.115 - 0.188 (0.0045 - 0.0074)
Limit0.24 (0.0094)
NOTE
*: Total indicator reading
CYLINDER BLOCK
NOTE
Unit: mm (in). Bore measurement at depths 20 (0.79), 60 (2.36) and 100 (3.94) mm from deck; X and Y axes orthogonal. A − B = taper, X − Y = out-of-round. Height "H" measured from crankshaft center to deck.
Surface flatness
StandardLess than 0.03 (0.0012)
Limit0.1 (0.004)
Height "H" (nominal)
Standard188.95 - 189.05 (7.4390 - 7.4429)
Limit—
Standard inner diameter — Grade No. 1
Standard71.0 - 71.010 (2.7953 - 2.7957)
Limit0.2 (0.008)
Standard inner diameter — Grade No. 2
Standard71.010 - 71.020 (2.9757 - 2.7961) [?]
Limit0.2 (0.008)
Standard inner diameter — Grade No. 3
Standard71.020 - 71.030 (2.7961 - 2.7965)
Limit0.2 (0.008)
Out-of-round (X − Y)
StandardLess than 0.015 (0.0006)
Limit—
Taper (A − B)
StandardLess than 0.010 (0.0004)
Limit—
Difference in inner diameter between cylinders
Standard0.05 (0.0020)
Limit0.2 (0.008)