TROUBLE DIAGNOSES — Trouble Diagnosis (without CONSULT) (Cont'd) — Diagnostic chart / Final check
BR-59spec tableFlash-code 10 is overloaded — it covers both 'ABS motor / motor relay / N.CVT input/output' and 'Brake lamp circuit'. The two are distinguished by whether fail-safe activates: motor/relay/CVT trips fail-safe, brake-lamp does not. Source prints '20 mph' here vs '19 mph (19 m/hr)' on adjacent pages — both refer to 30 km/h.
Trouble Diagnosis (without CONSULT) (Cont'd)
Diagnostic chart
1
DescriptionFr RH wheel sensor and harness
Detect — Engine runningX
Detect — Driving●
Fail-safe ON?●
Diagnostic procedure number1
2
DescriptionFr LH wheel sensor and harness
Detect — Engine runningX
Detect — Driving●
Fail-safe ON?●
Diagnostic procedure number1
3
DescriptionRr RH wheel sensor and harness
Detect — Engine runningX
Detect — Driving●
Fail-safe ON?●
Diagnostic procedure number1
4
DescriptionRr LH wheel sensor and harness
Detect — Engine runningX
Detect — Driving●
Fail-safe ON?●
Diagnostic procedure number1
5
DescriptionFr RH ABS solenoid and circuit
Detect — Engine running●
Detect — Driving●
Fail-safe ON?●
Diagnostic procedure number2
6
DescriptionFr LH ABS solenoid and circuit
Detect — Engine running●
Detect — Driving●
Fail-safe ON?●
Diagnostic procedure number2
7
DescriptionRr RH ABS solenoid and circuit
Detect — Engine running●
Detect — Driving●
Fail-safe ON?●
Diagnostic procedure number2
8
DescriptionRr LH ABS solenoid and circuit
Detect — Engine running●
Detect — Driving●
Fail-safe ON?●
Diagnostic procedure number2
9
DescriptionABS actuator relay and circuit
Detect — Engine running●
Detect — Driving●
Fail-safe ON?●
Diagnostic procedure number3
10
DescriptionABS motor, motor relay, N.CVT input, N.CVT output
Detect — Engine running●
Detect — Driving●
Fail-safe ON?●
Diagnostic procedure number4
10
DescriptionBrake lamp circuit
Detect — Engine running●
Detect — Driving●
Fail-safe ON?X*
Diagnostic procedure number4
11
DescriptionControl Unit power circuit
Detect — Engine running●
Detect — Driving●
Fail-safe ON?●
Diagnostic procedure number5
12
DescriptionControl Unit
Detect — Engine running●
Detect — Driving●
Fail-safe ON?●
Diagnostic procedure number6
Constantly ON
DescriptionABS actuator relay warning lamp and circuit
Detect — Engine running●
Detect — Driving●
Fail-safe ON?●
Diagnostic procedure number7
Constantly OFF
DescriptionABS warning lamp and circuit
Detect — Engine running●
Detect — Driving●
Fail-safe ON?X*
Diagnostic procedure number8
NOTE
Key:
*: ABS operates normally even when a fault is detected in the brake lamp and ABS warning lamp circuits.
●: Applicable
X: Not applicable
Final check
NOTE
After completing Trouble Diagnosis procedure, drive the vehicle for more than one minute at a speed higher than 30 km/h (20 mph). During this period, the warning lamp must not light up again.
See also
BR-60TROUBLE DIAGNOSES — Diagnostic Procedure 1 (Wheel sensor and harness)BR-61TROUBLE DIAGNOSES — Diagnostic Procedure 2 — ABS SolenoidBR-62TROUBLE DIAGNOSES — Diagnostic Procedure 3 — ABS Actuator Relay and Circuit (L.E.D. flashing number 9)BR-63TROUBLE DIAGNOSES — Diagnostic Procedure 4 — Actuator Motor Relay (L.E.D. flashing number 10)BR-67TROUBLE DIAGNOSES — Diagnostic Procedure 5 — ABS Control Unit Power Supply Circuit (L.E.D. flashing number 11)BR-68TROUBLE DIAGNOSES — Diagnostic Procedure 6 — ABS Control Unit (L.E.D. flashing number 12)BR-69TROUBLE DIAGNOSES — Diagnostic Procedure 7 — ABS Actuator Relay / ABS Warning or Circuit (L.E.D. continuously on)BR-70TROUBLE DIAGNOSES — Diagnostic Procedure 8 — ABS Warning Circuit (L.E.D. continuously off)